Search Results

In this paper we introduce an improved model for the fuel supply dynamics in an SI engine. First, we briefly investigate all the thermodynamic phenomena which are assumed to have a significant impact on fuel flow into the cylinder (i.e., fuel atomization, droplet decay, wall-wetting, film evaporation, and mixture flow back). This theoretical analysis results in a basic set of dynamic equations. Unfortunately, these equations are not convenient to use for control purposes. Therefore, we proceed to a simplified formulation. Several unknown parameters remain, describing phenomena which are difficult to quantify, such as heat and material transfer characteristics. These parameters are subject to operating conditions and are not discussed further. In order to validate the model dynamics, we refer to frequency and step response measurements performed on a 4-cylinder, 1.8 liter BMW engine with sequential fuel injection.

A fast, versatile nitric oxide (NO) measuring device applying the principles of chemiluminescence has been developed. This device consists of a small sensor head attachable to the engine exhaust system and a mobile cart containing all the necessary auxiliary aggregates and the signal processing unit. Optimization techniques based on a physico-chemical model and strict miniaturization were applied in the development of this NO measuring device. Subsequent tests utilizing a, solenoid valve and bottled calibration gas con- firmed the predicted dynamic behavior of the instrument. This device now shows an extremely short sampling delay and a higher bandwidth than common NO measuring devices can offer.

The two characteristics of wide-range air/fuel ratio sensors when located in front of and behind a three-way catalytic converter are investigated. Input as well as output gas concentration measurements and sensor readouts are presented. Behind a new converter almost no oxygen can be measured for rich air/fuel ratios. The wide-range sensor's signal is sensitive to changes in the gas composition when keeping the air/fuel ratio constant at a rich value. Since the gas compositions up- and down-stream of the converter differ, the sensor signals are not identical for the same rich air/fuel ratio before and after the converter. The various diffusion coefficients of the exhaust gas species flowing through the porous coating of the sensor combinded with the different up- and downstream gas compositions are responsible for the different sensor characteristics.

Modern model-based control schemes and their application on different engines need mathematical models for the various dynamic subsystems of interest. Here, the fuel path of an SI engine is investigated. When the engine speed and the throttle angle are kept constant, the fuel path is excited only by the fuel injected. Taking the NO concentration of the exhaust gas as a measure for the air/fuel ratio, models are derived for the wall-wetting dynamics, the gas mixture, as well as for the air/fuel ratio sensor. When only the spark advance is excited, the gas flow dynamics can be studied. A very fast NO measurement device is used as reference. Its time constant is below the segment time of one single cylinder (180° crank angle for a 4-cylinder engine), therefore its dynamics are much faster than the time constants of the systems investigated. A model structure considering the muliplexing effects of the discrete operation of an engine is given for the fuel path of a BMW 1.8 liter engine.

This paper describes the heat transfer model of a composite aluminum brake rotor and compares the predicted temperatures to dynamometer measurements taken during a 15 fade stop trial. The model is based on meshed surface geometry which is simulated using RadTherm software. Methods for realistically modeling heat load distribution, surface rotation, convection cooling and radiation losses are also discussed. A comparison of the simulation results to the dynamometer data shows very close agreement throughout the fade stop trial. As such, the model is considered valid and will be used for further Steel Clad Aluminum (SCA) rotor development.

A 1-D 2-layer model developed previously at MTU was used in this research to predict the pressure drop, filtration characteristics and various properties of the particulate filter and the particulate deposit layer. The model was used along with dilute emission data to characterize two catalyzed particulate filters (CPFs) having different catalyst loading and catalyst application processes. The model was calibrated and validated with data obtained from steady state experiments conducted using a 1995 Cummins M11-330E heavy-duty diesel engine with manual EGR with different fuels for the two different CPFs. The two different catalyzed particulate filters were CPF III (5 gms/ft3 Pt) and CPF V (50 gms/ft3 Pt). Both the CPFs had cordierite substrates with CPF III and CPF V had MEX and NEX catalyst type formulation respectively. The CPF III filter was catalyzed using a solution-impregnated process while the CPF V filter was catalyzed using a wash coat process.

This investigation is a continuation of a previous study by these authors in which a Lagrange polynomial interpolation method was developed to evaluate spray source terms and also to distribute the source terms onto the gas mesh; the method was applied to the liquid-gas momentum exchange. For this investigation, the method has been extended to the mass exchange between the liquid and gas phases due to evaporation. The Lagrange polynomial interpolation and source term distribution methods are applied to the liquid-gas mass and momentum exchange and are evaluated for evaporating sprays using KIVA3 as a modeling platform. These methods are compared with the standard “nearest neighbor” method of KIVA3, and experimental data are used to establish their validity. The evaluation criteria used include the liquid and vapor spray penetration, gas velocities and the computational stability.

The Vehicle Engine Cooling System Simulation (VECSS) computer code has been developed at the Michigan Technological University to simulate the thermal response of the cooling system of an on-highway heavy duty diesel powered truck under steady and transient operation. This code includes an engine cycle analysis program along with various components for the four main fluid circuits for cooling air, cooling water, cooling oil, and intake air, all evaluated simultaneously. The code predicts the operation of the response of the cooling circuit, oil circuit, and the engine compartment air flow when the VECSS is operated using driving cycle data of vehicle speed, engine speed, and fuel flow rate for a given ambient temperature, pressure and relative humidity.

Fuel spray-wall interaction frequently occurs on intake manifold wall in the port fuel injection engine and on the piston in the direct injection engine, especially during the cold start. The heat transfer between the spray and wall is involved in this interaction process and influences the dynamics of the impinged spray which can further affect the engine performance. The physics of impact dynamics of a single droplet serves as a fundamental for better comprehension of spray impingement. In our previous studies, we have focused on diesel droplets, at ambient temperature, impinging on both heated and non-heated wall and found impinged droplet morphology differences. To understand the effect of heat transfer and thermophysical properties on dynamics of droplet-wall interaction better, droplet temperature variation was introduced in this study. Therefore, different conditions were framed to explore the impact of thermophysical properties of the droplet.

To address the need of increasing fuel economy requirements, automotive Original Equipment Manufacturers (OEMs) are increasing the number of turbocharged engines in their powertrain line-ups. The turbine-driven technology uses a forced induction device, which increases engine performance by increasing the density of the air charge being drawn into the cylinder. Denser air allows more fuel to be introduced into the combustion chamber, thus increasing engine performance. During the inlet air compression process, the air is heated to temperatures that can result in pre-ignition resulting and reduced engine functionality. The introduction of the charge air cooler (CAC) is therefore, necessary to extract heat created during the compression process. The present research describes the physics and develops the optimized simulation method that defines the process and gives insight into the development of CACs.

This paper reports an experimental and numerical investigation on the spatial and temporal liquid- and vapor-phase distributions of diesel fuel spray under engine-like conditions. The high pressure diesel spray was investigated in an optically-accessible constant volume combustion vessel for studying the influence of the k-factor (0 and 1.5) of a single-hole axial-disposed injector (0.100 mm diameter and 10 L/d ratio). Measurements were carried out by a high-speed imaging system capable of acquiring Mie-scattering and schlieren in a nearly simultaneous fashion mode using a high-speed camera and a pulsed-wave LED system. The time resolved pair of schlieren and Mie-scattering images identifies the instantaneous position of both the vapor and liquid phases of the fuel spray, respectively. The studies were performed at three injection pressures (70, 120, and 180 MPa), 23.9 kg/m3 ambient gas density, and 900 K gas temperature in the vessel.

An automobile seat’s thermal performance can be challenging to quantify since it requires comprehensive human subject testing. Seat manufacturers must rely on subjective ratings to understand how the construction of a seat and its underlying heating and cooling technology may compare to other seats. Other factors may influence seat ratings published by global marketing information services companies (e.g., JD Power and Associates). In particular, occupants may be biased by the vehicle class in which a seat is installed and by how much the contribution of a specific vehicle’s HVAC system performance affects the perception of seat thermal comfort. Therefore, there is a need for an objective testing methodology that does not rely on human participants but is still capable of producing a thermal performance rating in terms of established thermal comfort scales.

Numerical investigation of engine performance and emissions of a six-stroke gasoline compression ignition (GCI) engine combustion at low load conditions is presented. In order to identify the effects of additional two strokes of the six-stroke engine cycle on the thermal and chemical conditions of charge mixtures, an in-house multi-dimensional CFD code coupled with high fidelity physical sub-models along with the Chemkin library was employed. The combustion and emissions were calculated using a reduced chemical kinetics mechanism for a 14-component gasoline surrogate fuel. Two power strokes per cycle were achieved using multiple injections during compression strokes. Parametric variations of injection strategy viz., individual injection timing for both the power strokes and the split ratio that enable the control of combustion phasing of both the power strokes were explored.

An over-expanded spark ignited engine was investigated in this work via engine simulation with a design constrained, mechanically actuated Atkinson cycle mechanism. A conventional 4-stroke spark-ignited turbo-charged engine with a compression ratio of 9.2 and peak brake mean effective pressure of 22 bar was selected for the baseline engine. With geometry and design constraints including bore, stroke, compression ratio, clearance volume at top dead center (TDC) firing, and packaging, one over-expanded engine mechanism with over expansion ratio (OER) of 1.5 was designed. Starting with a validated 1D engine simulation model which included calibration of the in-cylinder heat transfer model and SI turbulent combustion model, investigations of the Atkinson engine including cam optimization was studied. The engine simulation study included the effects of offset of piston TDC locations as well as different durations of the 4-strokes due to the mechanism design.

Automotive exhaust noise is one of the major sources of noise pollution and it is controlled by passive control system (mufflers) and active control system (loudspeakers and active control algorithm). Mufflers are heavy, bulky and large in size while loudspeakers have a working temperature limitation. Carbon nanotube (CNT) speakers generate sound due to the thermoacoustic effect. CNT speakers are also lightweight, flexible, have acoustic and light transparency as well as high operating temperature. These properties make them ideal to overcome the limitations of the current exhaust noise control systems. An enclosed, coaxial CNT speaker is designed for exhaust noise cancellation application. The development of a 3D multi-physics (coupling of electrical, thermal and acoustical domains) model, for the coaxial speaker is discussed in this paper. The model is used to simulate the sound pressure level, input power versus ambient temperature and efficiency.